Starting @ $2,750.00 13,500 Btu/h - 115 Volt Enlarged View (30 KB) 2600 Model Shown Main Product Page Product Description Typical Applications Technical Specifications Features & Benefits Options Installation & Operation Service & Warranty Dimensions How to Order Frequently Asked ???

PREPARING UNIT FOR OPERATION
INSTALLATION

Be sure to read and familiarize yourself with the complete manual that comes with the unit before installing and operating COOLIT2000 Series.  The COOLIT2000 Series operation and installation manual is located in the white envelope.

Your new COOLIT unit has passed a double quality assurance program; once before leaving the factory and again before leaving the regional warehouse. If you find shipping damage please contact both ADAPT and the point of purchase immediately. DO NOT OPERATE THE UNIT.

To further prepare the unit for operation proceed as follows:

START UP PROCEDURE

1. Unpack COOLIT2000 Series.

Unpack and inspect the unit for visible shipping damage. If you find shipping damage, DO NOT OPERATE THE UNIT. Keep all packaging.

2. Remove COOLIT2000 Series from skid.

The COOLIT2000 Series is immobilized on the skid by two wheel lock panels. Each wheel lock panel is secured with two screws. Remove the screws from the front wheel lock panel. Gently push the unit from the back to roll the front wheels off onto the floor. Lift the unit from the skid using the recessed hand hold area in the back of the unit. Gently set unit down on the floor.

3. Place the unit on a flat, solid surface.

Make sure unit is on a flat surface before removing front wheel chock. Unit could unexpectedly roll and cause personal injury or property damage.  Operation on uneven surfaces may cause vibration, noise and possible water leakage from condensate tank(s).

4. Check that the condensate water tanks are in place and properly seated.

If the condensate tank(s) are not installed properly the unit will not operate properly. The unit will display a yellow light.

5. Air discharge kit installation.

The exhaust system in integral to the unit. No tools are required for this installation.

1. Slowly lift the ceiling panel from the top of the unit. The exhaust duct is attached and will extend from the unit.

2. Move the ceiling tile out of the grid by pushing up on one end and sliding it back 10-12 inches.

3. Put the ceiling panel into the ceiling tile grid. Make sure the ceiling panel is positioned properly in the ceiling grid and cannot fall out. There should be at least 18 - 24" of open space above the ceiling panel outlet so exhaust air is not blocked.

4. For permanent installation cut the ceiling tile so the tile will lay back in the grid. For temporary installations simply slide the ceiling tile tight against the ceiling panel so when the COOLIT and ceiling panel are no longer in use you can simply move the ceiling tile back into place.

6. Plug COOLIT unit into wall outlet.

Plug the COOLIT2000 Series  into a NEMA 5-15 outlet. Plug unit directly into the appropriate wall outlet. Do not plug the COOLIT2000 Series into extension cord. When power is applied to the unit, the LED display will read "OFF".

If using an extension cord: extension cord must be rated at least 15 amps, at 120 volts and have a grounding type attachment plug connector (load fitting).

7. Turn the COOLIT unit on.

Turn the COOLIT2000 Series on by pushing the “ON/OFF” button. To turn the unit on, select either FAN ONLY or COOL mode. When you select COOL the compressor will not engage immediately. There is a 3 - 5 minute time delay.

8. Set the desired function mode and fan speed.

Select either LOW FAN, HIGH FAN or AUTOMATIC. The fan speed selector controls the evaporator fan speed in both the FAN ONLY and COOL modes.

9. Set the desired temperature.

To set the temperature you must select a setting using the “+” and “-” buttons on the control panel. The settings range from 60° to 85°F.

10. Set-up the condensate pump (OPTIONAL).

To set-up the condensate pump for continual automatic removal of condensate refer to the Condensate Pump instructions on page 13 of this manual.

11. Shut off the COOLIT2000 Series.

To shut down the COOLIT2000 Series press the “ON/OFF” button until “OFF” is displayed in the LED window. Since the unit is still plugged into the wall outlet the LED window will read “OFF”. This is normal and indicates that there is power to your unit.

W A R N I N G:

To reduce risk of fire or electric shock do not expose unit to rain or moisture. Do not open cabinet while unit is connected to a power source. Dangerous voltage is present. Have repairs performed by certified HVAC technicians.

MAINTENANCE

C A U T I O N
To avoid injury or fatality from electrical shock, turn the unit off and unplug before performing maintenance or cleaning. Do not spray with water or any liquid! 

Air Filter: Clean the air filter every two to three weeks or as required by the environment and usage. A dirty filter will reduce the cooling of the unit. Clean the filter by vacuum or wash with a mild detergent and air dry.

Air Intakes: Keep 'em clean! Use a vacuum or soft brush. 

Exterior Surfaces: Wipe it down with a damp soft cloth or sponge. Don't use any chemicals or other junk - you'll just ruin your machine. 

Water Tanks: Keep 'em clean. Use a mild soap and make sure to rinse it well.